Most quality disputes with suppliers start with a sentence that seemed clear when it was written: "good finish", "strong packaging", "same as sample". A quality specification replaces those phrases with criteria that a factory supervisor, a line worker and an inspector would all interpret the same way.
What should a quality specification include? A quality specification should include: (1) scope and revision control, (2) reference samples, (3) critical dimensions and tolerances, (4) materials and components, (5) appearance and finish criteria, (6) function and performance tests, (7) labelling and marking, (8) packaging, (9) defect classification and AQL levels, and (10) approval and change control.
Below, each section is explained, followed by guidance on tolerances, sign-off, writing for Chinese factories, and a copyable template.
Quality specification, product specification and inspection checklist: what is the difference?
Three documents are often confused. They work together, but each has its own job.
| Document | Main question it answers | Used by | When it is written |
|---|---|---|---|
| Product specification | What exactly are we making? (design, function, materials, dimensions) | Factory engineers and quoting staff | Before quotations and sampling |
| Quality specification | How do we decide whether a finished unit is acceptable? | Factory QC, inspectors, buyer | After the sample is approved, before bulk production |
| Inspection checklist | What will the inspector check on the day, and how? | Inspector | Before each inspection |
The product specification, the subject of a planned guide on writing product specifications for Chinese factories, tells the factory what to build. The quality specification tells everyone how to judge what was built. The product inspection checklist then turns the quality specification into a practical, step-by-step inspection form.
The ten sections of a quality specification
1. Scope and document control
State the product name, SKU or model number, variants covered (colours, sizes), the purchase order or programme it applies to, the revision number and date, and which other documents it refers to (drawings, product specification, packaging specification). Without a revision number, factories and inspectors can end up working from different versions.
2. Reference samples and order of precedence
List the approved reference samples: the sealed golden sample, any boundary samples showing acceptable colour or cosmetic limits, and approved material swatches. Then state the order of precedence when documents disagree. A common approach is: written specification for measurable characteristics; golden sample for appearance, colour and feel; drawings for anything not covered by either.
3. Critical dimensions and tolerances
List only the dimensions that matter to function, fit, safety or customer perception, each with a nominal value, tolerance, measuring tool and number of units to measure. Typical critical dimensions are those that affect assembly (a lid that must fit a jar), compatibility (a part that must fit a standard component) or regulation (a small part’s size).
4. Materials and components
Specify materials by grade or standard where possible, not just by name ("304 stainless steel", not "stainless steel"), plus any components that must come from a named or approved source. State what changes require your approval: a different resin supplier, a different fabric mill, a substitute battery. Material substitution without notice is one of the most common causes of quality drift in repeat orders.
5. Appearance and finish
Cosmetic criteria are where most arguments happen. Make them inspectable:
- Define surfaces by visibility. For example, Surface A (seen in normal use), Surface B (seen occasionally), Surface C (hidden). Allow different limits for each.
- Define how to look. State a viewing distance, lighting condition and viewing time for cosmetic checks, so inspectors do not search for marks nobody would notice.
- Quantify defects. Maximum scratch length, number of specks per surface, acceptable colour difference against the golden sample or boundary samples.
- Cover print and logos. Position, size, colour and adhesion.
6. Function and performance tests
List each test the factory and inspector must perform, with method, equipment, sample quantity and pass criterion. Examples: assembly and operation test, on/off and charging test for electronics, zip pull test for bags, water-leak test for bottles, carton drop test. If a test needs laboratory equipment or a recognised standard method, say whether an external lab report is required and for which batches.
7. Labelling and marking
Specify product labels, rating plates, care labels, warning text, country-of-origin marking, barcodes and any market-required marks. Regulatory labelling depends on the destination market and changes over time, so confirm current requirements with the relevant authority or a compliance professional; the specification should record what you have decided, not guess it.
8. Packaging
Reference your packaging specification rather than repeating it. Our packaging specification checklist covers retail packs, inner and master cartons, inserts and marks. In the quality specification, add the packaging checks that decide acceptance: carton condition, barcode scan, carton drop test and shipping-mark accuracy.
9. Defect classification and AQL
Attach a product-specific defect list that sorts each foreseeable defect into critical, major or minor (see our guide to classifying critical, major and minor defects). Then state the sampling plan: inspection level and AQL per class. Many buyers use ISO 2859-1 General Inspection Level II with zero tolerance for critical defects and separate AQL values for major and minor defects; the right values depend on the product and your market. Our explainer on AQL values and sample sizes shows how those numbers translate into accept/reject limits.
10. Approval, sign-off and change control
Record who approved the specification on each side, the date and revision, and the rule for changes: any change to materials, components, process, tooling or sub-suppliers must be notified in writing and approved before use, and may require a new golden sample.
How tight should tolerances be?
As tight as the function requires, and no tighter. Tighter tolerances mean more precise tooling, slower processes, more inspection and higher reject rates, all of which raise the price or tempt a factory to quote one standard and produce to another.
A practical approach:
- Identify critical-to-function dimensions. Ask what happens if the dimension is off. If the answer is "the lid won’t close", it is critical. If the answer is "nobody will notice", it is not.
- Set specific tolerances only on critical dimensions. Base them on the fit or function they protect, and on the factory’s process capability for that material and method.
- Apply a general tolerance to everything else. Many drawings state a general tolerance class, such as those defined in ISO 2768 (general tolerances for linear and angular dimensions, with classes from fine to very coarse), so that every untoleranced dimension still has a limit. ISO 2768 was written mainly with machined parts in mind; for moulded plastics, castings, sheet metal or textiles, ask the factory which general tolerance standard or practice it works to, and confirm the edition both sides use.
- Ask the factory before you finalise. If a factory says a tolerance is not achievable with its current process, believe it, and decide whether to relax the tolerance, change the process or change the supplier.
- Say how it will be measured. A tolerance without a measuring method (calliper, gauge, coordinate measuring machine, tape) invites disagreement.
For soft goods and non-rigid products, tolerances are usually expressed differently, for example graded measurement charts for garments. Our planned tech pack guide for garment suppliers covers that format.
Who signs off a quality specification?
Usually three parties:
- The buyer: the product owner or quality lead who has authority to accept or reject goods.
- The factory: ideally the QC manager or engineering lead, not only the salesperson, because they are the ones who must produce to it.
- The inspector or sourcing partner: they should confirm the document is inspectable and raise anything they cannot check.
Sign-off should happen after sample approval and before bulk production starts. Keep the signed version, ideally bilingual, with the purchase order so it forms part of what was agreed. If you are developing a custom product, sign-off normally follows the final development round; our upcoming guide to custom sample development covers those rounds.
Writing for Chinese factories: practical tips
- Numbers, not adjectives. "Max. 2 visible specks per Surface A at 50 cm" can be checked; "clean finish" cannot.
- One requirement per line. Numbered lines make it easy to reference in reports and corrective actions.
- Pictures with arrows. Annotated photos of the golden sample and of unacceptable examples cut misunderstanding more than any amount of text.
- Bilingual where possible. Provide English and Chinese text side by side, and have the factory confirm the Chinese wording matches its understanding.
- Consistent units. Use metric units throughout, and state units on every value.
- Avoid absolute promises. "No defects" is not a specification. Define what is acceptable, what is not, and how many can be tolerated in a sample.
Hypothetical example: a buyer’s original note said "handle must be strong". The revised specification line reads: "Handle pull test: apply a 10 kg static load for 60 seconds; no deformation, cracking or detachment. Test 5 units per inspection." The second version can be passed or failed; the first cannot. (Load values here are illustrative only; set yours from the product’s real use.)
Quality specification template
Copy and adapt this outline:
| No. | Section | What to fill in |
|---|---|---|
| 1 | Document control | Product, SKU/variants, PO or programme, revision no., date, linked documents |
| 2 | Reference samples | Golden sample ID and seal number, boundary samples, swatches, order of precedence |
| 3 | Critical dimensions | Dimension, nominal, tolerance, tool, quantity measured; general tolerance class for the rest |
| 4 | Materials and components | Material grades, approved component sources, changes requiring approval |
| 5 | Appearance and finish | Surface zones, viewing conditions, limits per defect type, print and logo criteria |
| 6 | Function and tests | Test name, method, equipment, quantity, pass criterion, external lab requirement |
| 7 | Labelling and marking | Product labels, warnings, origin marking, barcodes, market marks (verified by buyer) |
| 8 | Packaging | Reference to packaging specification; carton, barcode, drop test and mark checks |
| 9 | Defects and AQL | Defect list by class; inspection level; AQL for critical, major, minor |
| 10 | Approval and changes | Signatures and dates (buyer, factory, inspector), change-notification rule |
Common mistakes to avoid
- Writing the quality specification after production has started.
- Tolerancing every dimension tightly "to be safe".
- Relying on the golden sample alone for measurable characteristics.
- Letting the salesperson sign off without involving factory QC.
- Not updating the specification after an approved change, so the inspector checks against an old version.
- Leaving out the defect list, which forces the inspector to classify defects on their own judgement.
When an order does fail, a clear specification is what makes handling a failed inspection a factual discussion rather than an argument, and it makes the inspection report far easier to read.
Bangladesh importers
For goods imported into Bangladesh, record in the specification any product requirements you have confirmed for the local market, such as labelling or product standards that may be relevant under BSTI rules. These requirements change and depend on the product, so verify them with the relevant authority or a compliance professional before finalising the document, and make sure the factory knows which marks or labels must appear.
Turning the specification into inspections
A specification only protects you if it is used at inspection. Jingxin Sourcing carries out product and packaging inspections at supplier sites in Yiwu, Shenzhen and Guangzhou; see our quality-control services in China for how inspections are arranged. Whether you then use an independent inspector, your sourcing partner’s QC team or both is the subject of our next article, comparing third-party inspection with sourcing-company quality checks. If you are still at the development stage, the custom product sourcing support covers samples and prototypes before the specification is finalised. For the full inspection sequence the specification feeds into, see our guide to QC stages when sourcing from China.
Frequently Asked Questions
Closing thought
A good quality specification is short on adjectives and long on numbers, pictures and signatures. Write it once with the factory’s QC team at the table, keep it under revision control, and it becomes the shared language for every inspection, report and corrective action that follows.