Jingxin Sourcing

How to Read a Product Inspection Report

Inspection reports are written for people who read them every day. If you only receive a few a year, the AQL tables, defect codes and photo grids can hide the one line that matters. This guide reads a report the way an experienced buyer does: verdict first, then the evidence behind it.

How do you read an inspection report? Start with the overall result (pass, fail or pending) and the reason for it. Then check the AQL summary: sample size, defects found and the accept/reject limits. Next read the defect list, measurements and test results, and finally use the photos to confirm what the inspector describes.

The standard sections of an inspection report

Report layouts vary between inspection providers, but most product inspection reports from China follow a similar structure.

Report section What it shows What to check first
Header / order information PO number, product, supplier, inspection type, date and location, inspector That it is your order, your product version and the inspection stage you booked
Overall result Pass, fail or pending, often with a one-line reason Which section caused anything other than a pass
AQL and sampling summary Lot size, inspection level, sample size, AQL per defect class, accept/reject numbers, defects found Defects found versus the reject number for each class
Quantity and packing status Units produced, units packed, cartons counted That production was finished and goods were packed when inspected
Defect list Each defect type, its classification and count, often with photo references Whether classifications match your own defect list
Measurements and on-site tests Dimensions, weight, function, drop or barcode tests, and their results Out-of-tolerance readings and any test marked "not done"
Packaging and marking Retail box, inner and master cartons, labels, shipping marks Errors that could block a sale or delay customs
Photos Product, defects, measurements, packaging, warehouse That photos match the descriptions and show your goods
Remarks Inspector notes, factory comments, deviations from the plan Anything the inspector could not check

Our product inspection checklist template mirrors these sections from the buyer’s side, which makes reports far easier to read.

Reading each section

1. Header and order information

Do not skip it. Check the purchase order number, SKU, colour and quantity. A report for the wrong variant, or a during-production check booked as a final one, changes what the result means. Also note who was present and where the inspection happened: at the factory, a warehouse or a consolidation point.

2. Overall result

Reports usually show one of three verdicts:

  • Pass: all defect classes are within the accept numbers and no required check failed.
  • Fail: at least one defect class exceeded its reject number, a critical defect was found where none is allowed, or a required test failed.
  • Pending (or "hold"): the inspector cannot conclude without a decision from you.

A pass is not a guarantee that every unit is perfect. AQL sampling accepts a small number of defects by design. A fail does not mean every unit is defective either. If your order failed, our guide on what to do when a shipment fails inspection covers the options.

3. AQL and sampling summary

This table is the core of the report. Read it line by line:

  • Lot size: the number of units in the batch inspected.
  • Inspection level: usually General Inspection Level II under ISO 2859-1 unless you asked for another.
  • Sample size: derived from the lot size and inspection level.
  • AQL per defect class: for example, 0 for critical, 2.5 for major, 4.0 for minor, if that is what you specified.
  • Ac / Re: the acceptance number (maximum defects allowed) and the rejection number (the count at which the lot fails).
  • Found: the defects actually recorded in each class.

If the "found" count reaches the Re number in any class, that class fails. If you need a refresher on how these numbers are derived, see what AQL means and how sample sizes are set.

4. Defect list

The defect list explains the numbers. Each line should name the defect, its location, its classification and how many times it was found. Check two things:

  • Classification. Is a loose handle recorded as minor when you consider it major or critical? Inspectors classify against your instructions; if you did not give any, they use their own judgement. Our guide to critical, major and minor defects explains how to set your own list.
  • Concentration. Are most defects one type? A single repeated defect often points to one station or one material batch, which is easier to fix than scattered problems.

5. Quantity and packing status

Most final inspections assume production is complete and most goods are packed. If the report shows that a large share of the order was still in production or unpacked, the sample may not represent the full shipment. Note the numbers and decide whether a further check is needed.

6. Measurements and on-site tests

Look for measurements outside tolerance and tests that were "not performed" or "not applicable". A test is sometimes skipped because the equipment was not available or the method was not specified, which is a gap in coverage rather than a pass.

7. Packaging and marking

Retail packaging errors (wrong barcode, missing warning text, misprinted logo) can stop goods being sold even if the product is perfect. Carton marks and labels matter for receiving and customs. Packaging defects are often listed separately from product defects. A dedicated guide to packaging quality checks before shipment is planned later in this series.

8. Photos

Photos are evidence, not decoration. Check that:

  • the products, cartons and labels shown are clearly yours;
  • each listed defect has at least one photo;
  • measurement photos show the reading on the tool;
  • there is a photo of the carton selection or warehouse, showing samples were drawn from across the lot.

9. Remarks

The remarks often contain the most useful information: what the inspector could not check, deviations from the plan, the factory’s response and whether a reference sample was available. Read them before deciding anything.

A fictional annotated example

Hypothetical example. The data below is invented to show how the sections connect. It does not describe a real order, supplier or report format.

Product: ceramic coffee mug, 350 ml, printed logo. Order: 3,000 units. Inspection: pre-shipment, General Inspection Level II, single sampling, normal inspection.

Field Hypothetical value Annotation
Lot size 3,000 units Falls in the 1,201–3,200 range, which gives code letter K at Level II
Sample size 125 units Standard sample for code letter K
Critical (AQL 0) Found 0 Zero tolerance; passes
Major (AQL 2.5), Ac 7 / Re 8 Found 9 9 reaches and exceeds the Re of 8: fails
Minor (AQL 4.0), Ac 10 / Re 11 Found 6 Within the accept number; passes
Main major defect Logo print smudged, 7 of 9 majors Concentrated defect: likely one printing issue, so rework or sorting is realistic
Measurement: height 95 mm ±1 mm 5 of 5 measured within tolerance No dimensional concern
Drop test (carton) Passed, no breakage Packaging protection adequate for this check
Quantity packed 3,000 units, 100 cartons Fully packed; sample represents the shipment
Overall result Fail (major defects) Driven by one defect type; ask for sorting of print defects, then re-inspect

The useful reading is not "the mugs failed" but "the logo printing failed, everything else passed". That changes the conversation with the factory from a dispute about the whole order to a request to sort and reprint one defect type.

What does "pending" mean on an inspection report?

"Pending" means the inspector could not give a pass or fail because something needs your decision. Common reasons:

  • No reference sample or unclear specification. The inspector cannot judge colour, finish or a tolerance without an approved standard. A sealed golden sample prevents this.
  • A finding outside the checklist. For example, a design difference that may or may not be an approved change.
  • Test results to follow. A sample has been sent for laboratory testing.
  • Quantity or packing incomplete. Not enough goods were ready to inspect the full lot.
  • A disputed classification. The factory disagrees with the inspector’s call.

Respond quickly and in writing: confirm whether the finding is acceptable, defective or needs a further check. Until then, treat a pending result as unresolved. A clear written quality specification, the subject of our next guide in this series, is the best way to reduce pending results.

Which section of an inspection report matters most?

The AQL summary and defect list together. They show whether the order passed and why. Critical defects deserve attention even if the overall result is a pass, because some providers record a critical defect in remarks rather than failing the lot if your instructions did not set zero tolerance. After that, the remarks section matters most because it shows what was not checked.

Inspection report glossary

Term Meaning
AQL Acceptable Quality Limit: the worst average defect level tolerated for a defect class under ISO 2859-1 sampling
Inspection level How large the sample is relative to the lot; General Level II is the usual default
Code letter Letter derived from lot size and inspection level that sets the sample size
Ac / Re Acceptance and rejection numbers for each defect class
Critical defect Could cause harm or breaks mandatory rules
Major defect Likely to cause product failure or a return
Minor defect Departure from standard unlikely to affect use
PSI Pre-shipment inspection, done when goods are finished and packed
DUPRO During-production inspection
Golden sample Approved, sealed reference unit
N/A or not performed Check not done; a gap in coverage, not a pass
Pending / hold Inspector awaits the buyer’s decision
Concession Buyer accepts a deviation in writing

Red flags in an inspection report

  • Photos do not match the product, or the same photo appears for different defects.
  • All sample cartons appear to come from one stack or one pallet.
  • Sample size is smaller than the AQL table requires, with no explanation.
  • Key tests marked "not performed" without a reason.
  • Defect counts that add up differently in the summary and the list.
  • No remarks at all on a complex product.

Any of these is a reason to ask the inspector to explain before releasing payment. If you are weighing who should inspect your goods in the first place, our upcoming comparison of third-party inspection and sourcing-company quality checks looks at independence and reporting.

What to do after reading the report

  • Pass: release the balance and shipment as agreed, and file the report with the order records.
  • Fail: hold payment, agree a remedy and re-inspect.
  • Pending: answer the inspector’s question in writing within a set time.
  • Repeated issues: ask the supplier for a corrective action plan. A guide to root-cause and corrective-action basics follows in this series.

Bangladesh importers should keep the report with the shipping documents. It is useful evidence in a later claim, and some buyers present inspection certificates under payment terms agreed with their bank; check what your bank and contract require.

Inspection reports from Jingxin Sourcing

Jingxin Sourcing carries out product and packaging inspections at supplier sites, with staff active in Yiwu, Shenzhen and Guangzhou. To see how inspections are scoped and booked, visit our quality-control and inspection service. If the report leads you to change supplier, the China product sourcing service can help shortlist alternatives. For the bigger picture of where each inspection sits, start with the QC stages guide and the pre-shipment inspection overview.

Frequently Asked Questions

In short

An inspection report answers one question, "can this lot ship?", and then shows its working. Read the verdict, check it against the AQL numbers, look for what drove it and what was not checked, and let the photos confirm the story. A report you understand is one you can act on the same day.

Share This Article:
Jingxin Editorial Team
Published By

Jingxin Editorial Team

Sourcing and supply chain specialist at Jingxin Sourcing, providing practical insights on supplier evaluation, quality control, manufacturing tooling, and overseas procurement.

SOURCING & LOGISTICS ADVISORY

Need Help Sourcing from China for Bangladesh?

Jingxin Sourcing supports Bangladesh importers, and buyers in nearby South Asian markets, across product sourcing, supplier verification, quality control, custom packaging and China-to-Bangladesh shipping. Speak directly with our Dhaka or Yiwu team.

WhatsApp Enquiry (+880 1747 736 000) Request a Quote
Dhaka Head Office: 2/2, Pallabi Main Road, Mirpur-1216 Yiwu China Office: Fan Cun, Jiangdong Subdistrict

Leave a Reply / Question

Your email address will not be published. Required fields are marked *